SECTION 6
AUTO TUNE KITS FOR POWER COMMANDER V
  • Plugs directly into the Power Commander V with a single cable
  • Includes 18mm O 2 sensors and power connector that plugs into the bike’s harness
  • Makes automatic fuel adjustments
  • User can specify what air/fuel ratio to make each rpm and throttle position percentage combination
  • Makes it possible to adjust cruise for best fuel economy as well as larger throttle openings for peak power
  • Base settings included for air/fuel ratios, but are fully adjustable if need be
  • Made in the U.S.A.
  • NOTE: Because of possible clearance issues, some aftermarket exhaust systems may require modifications or relocation of their sensor bungs.
    PART #
    DESCRIPTION
    SUG. RETAIL SEATS &
    1020-1559 1
    For 14-18 Dressers, 12-17 FXS/ FLS/ FLST, Dyna Glide and 12-17 XL models w/ CAN-bus 6-pin connector
    $479.95 SISSY BARS
    1020-1117 1
    For 10-13 Dresser models w/ 12mm O 2 sensor (except FXST/ FLST, Dyna Glide 4-pin connector models)
    479.95
    1020-0857
    For all models w/ 18mm O 2 sensors (except 11 FXST/ FLST 6-pin connector models)
    469.95
    1020-1558
    For 11 FXS/ FLST models w/ CAN-bus 4-pin connector
    469.95
    1 Requires installation of two 18mm sensor bungs (included).
    TARGET TUNE
  • Allows the factory ECM to interpret and use wideband
  • O 2 sensor signals
  • Target fuel table from the calibration is achieved in real time
  • Retains OEM closed loop and achieves adaptive fuel control strategy
  • Learns and uses VE table corrections as you ride
  • Does not interfere with dealer diagnostic/service tools
  • Includes OEM style connectors to plug into factory O 2 harness, either 2- or 4-pin versions
  • 1020-2483
  • Available with or without O 2 sensor
  • PART #
    DESCRIPTION
    SUG. RETAIL PART #
    DESCRIPTION
    SUG. RETAIL & DRIVELINE
    WITH O 2 SENSORS
    WITHOUT O 2 SENSORS
    1020-2483
    For 07-09 Dressers, 07-11 FXST/ FLST
    1020-2484
    For 07-09 Dressers, 07-11 FXST/ FLST
    (except 07-11 CVO models), 06-11 Dyna Glide,
    (except 07-11 CVO models), 06-11 Dyna Glide,
    08-11 V-Rod, and 07-13 XL models
    $599.95
    08-11 V-Rod, and 07-13 XL models
    $299.95 & SEALS
    1020-2485
    For 10-13 Dresser models
    599.95 1020-2486
    For 10-13 Dresser models
    299.95
    1020-2487
    For 12-17 V-Rod models
    599.95 1020-2488
    For 12-17 V-Rod models
    299.95
    1020-2489
    For 12-17 FXST/ FLST and 12-17 Dyna Glide models
    599.95 1020-2490
    For 12-17 FXST/ FLST and 12-17 Dyna Glide models
    299.95
    1020-2491
    For 14-18 Dresser models
    599.95 1020-2492
    For 14-18 Dresser models
    299.95
    1020-2495
    For 14-18 XL models
    599.95 1020-2496
    For 14-18 XL models
    299.95
    1020-2493
    For 15-18 XG 500/ 750 models
    599.95 1020-2494
    For 15-18 XG 500/ 750 models
    299.95
    MULTI-FUNCTION
    1020-0326
    HUB ACCESSORY
    FOR POWER
    COMMANDER
    USB/USB-EX
  • The Multi-Function
  • Hub allows access to
    advanced expansion
    features of the Power
    Commander USB
  • Compatible with the LCD display, but the display is not required
  • 1020-0327
  • Four separate functions can be accessed with the Multi-Function Hub
  • The Map Selection Switch ( 7 / 8 ” bar mount) allows the rider to switch
  • between two different maps in the Power Commander; this allows a
    map for economy, and a separate map for performance
  • The Gear Position/Speed function allows fuel and timing adjustments
  • to be made depending on the gear selected and the position of the
    throttle, up to +/-50% fuel and +/-10 degrees of timing
  • Pressure input allows the fuel to be increased, along with the boost
  • level on turbocharged installations; the change of boost level does
    not require a re-mapping of the Power Commander
  • Relay outputs allow up to two warning lights or relays to be triggered independently to activate items such as shift lights, nitrous systems,
  • or air shifter; the trigger can be by throttle percent, rpm, or both
  • Comes complete with installation instructions, wiring diagrams and CD with the required software updates
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    1020-0326
    Multi-Function Hub and wiring harness for Map Selection Switch only
    $179.95 FENDERS
    1020-0327
    Multi-Function Hub and wiring harness for Map Selection, Gear Position, Speed sensor, Pressure Input and two relay outputs
    219.95 & LICENSE
    POD-300 DIGITAL DISPLAY
  • Real-time fuel adjustment
  • Display channels real-time: RPM, TP, map position (when using map switch), duty cycle, fuel exchange,
  • ignition change and wideband air/fuel ratio (with WB2 or auto-tune connected)
  • Weather resistant for use in all conditions
  • Log channels saved to internal memory and can be viewed/analyzed with Dynojet’s powercore software
  • High-contrast display, viewable in sunlight
  • Includes CAN cable for attachment to Power Commander V,
  • Auto Tune and Wide Band Power Commander
    PART #
    DESCRIPTION
    SUG. RETAIL
    NOTE: Not for use with Power Commander III USB.
    1020-2371
    POD-300 digital display
    $249.95
    DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES.
    SEE PAGE 396 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION.
    577