SECTION 10
CAN-BUS WIRING HARNESS EXTENSIONS
  • Plug-N-play wiring harnesses to complete your handlebar wiring job
  • Sold in a variety of pre-finished lengths to accommodate the most common bar jobs
  • Made in the U.S.A.
  • 2120-0880
    P ART  #
    DESCCRIPTION
    SUG. RETAIL P ART  #
    DESCCRIPTION
    SUG. RETAIL P ART  #
    DESCCRIPTION
    SUG. RETAIL
    FOR 14-18 DRESSERS (EXCEPT FLHRXS)
    FOR 14-18 DRESSERS (EXCEPT FLHRXS) (CONT)
    FOR 14-18 DRESSERS (EXCEPT FLHRXS) (CONT)
    2120-0880 36” Long (6+ over stock)
    $66.95 2120-0882 42” Long (12+ over stock)
    $69.95 2120-0884 48” Long (18+ over stock)
    $73.95 SISSY BARS
    2120-0881 39” Long (9+ over stock)
    67.95 2120-0883 45” Long (15+ over stock)
    71.95
    2050-0246
    2050-0245
    CAN-BUS CONTROLLERS
    REPLACEMENT CANBUS
  • A CAN-bus controller is an absolute necessity when changing handlebars and switches on any
  • ELECTRICAL CONNECTION
    11-16 model because of the factory CAN-bus handlebar switch assemblies that make changing
  • OEM replacement electrical power connection & SEALS
  • these handlebars next to impossible
  • For navigation, audio, tachometers, oil
  • So simple to use; just plug the unit into the factory harness under the fuel tank and wire up
  • pressure gauges and heated grips
    any pre-CAN-bus handlebar switch assemblies of your choice
    P ART  #
    DESCRIPTION
    SUG. RETAIL
  • Made in the U.S.A.
  • 2120-0676 For 14-18 XL,
    NOTE: Does not work with Keyless Ignition Bikes
    11-17 FXST/ FLST, 12-17 Dyna
    $25.95
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    2050-0246
    For 14-18 FLHT/ FLHX/ FLHR/ FLTRX
    $275.95
    2050-0245
    For 11-18 FXST/ FLST, 12-17 Dyna, 14-18 XL
    275.95
    2120-0595
    MOMENTARY SWITCH
    CONVERTER
  • Intended for custom
  • applications where
    2120-0594
    momentary switches are used
    IGNITION WIRING HARNESSES
    for a HIGH/ LOW headlight
  • Match OEM H-D specs
  • switch and RUN/ KILL switch
  • Simple, plug-and-play installation
  • Module converts the momentary switch into
  • Made in the U.S.A.
  • a HIGH/ LOW latching and an ON/ OFF latching
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    for a run switch
    2120-0595
    For 01 Touring models w/ crank position sensor only; repl. OEM #32435-01
    $139.95 •Made in the U.S.A.
    2120-0594
    For 00 Touring models w/ crank and cam position sensors; repl. OEM #32435-00
    139.95 P ART  #
    DESCRIPTION
    SUG. RETAIL & GAUGES
    2120-0818 1 For 99 Touring models; repl. OEM #32435-99
    149.95 2050-0244
    Momentary
    1 Used when converting Magnetti Marelli EFI to carb.
    switch converter
    $99.95
    Y POWER TAP HARNESS
    2130-0138
  • Gives you two available ports to tap for
  • 12-VOLT POWER CONNECTION
    12V switched power; works great for testing,
  • Replacement accessory connection
  • using the OBDP and keeping your optional
  • Used for amp and speaker systems,
  • accessory plug in at the same time
    GPS, heated grips and seats, and
  • Made in the U.S.A.
  • decorative lighting
    PART #
    DESCRIPTION
    SUG. RETAIL & AXLES
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    2130-0138
    For 99-11 Touring models
    $21.95
    2120-0894
    For 14-18 Touring models
    $24.95
    2120-0810
    For 11-13 Softail, 12-13 Dyna, and all 14-18 models
    23.95 HARDWARE,
    DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES.
    SEE PAGE 396 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION.
    949