ELECTRICAL & GAUGES
RACING WIRES AND ACCESSORIES
  • Outer insulator of rugged, high-performance silicone and inner core of solid copper wire strands
  • Connected with NGK resistor covers in either straight or 90° configurations
  • Fit most applications for snowmobiles, ATVs, motorcycles, watercraft and carts
  • Resistor cover comes equipped with a 5k-ohm ceramic resistance to defend against radio frequency
  • CR18035
    interference that can disrupt electronic ignitions
  • Wire/ cover sets are available for plugs with removable terminals and for solid terminals in 50cm (19 1 / 2 ”) and 100cm (39”) lengths
  • Wire connector makes attaching new wires to CDI unit easy – just insert the lead from the CDI unit in one end
  • and the new wire in the other, then screw the two pieces together for a watertight seal
  • Wire connector made of high-impact plastic
  • J18083
    DESCRIPTION
    P ART  #
    SUG. RETAIL
    Straight cover, 50cm, removable
    CR18035
    $21.95
    DESCRIPTION
    P ART  #
    SUG. RETAIL
    90° cover, 50cm, removable
    CR28048
    21.95
    90° cover, 100cm, removable
    CR58515
    $21.95
    Straight cover, 50cm, solid
    CR38089
    21.95
    90° cover, 100cm, solid
    CR68736
    21.95
    90° cover, 50cm, solid
    CR48054
    21.95
    Wire connector
    J18083
    6.95
    RESISTOR COVERS
  • NGK spark plug resistor covers
  • used with resistor spark plugs are
    L: 90º
    the best combination against radio
    Elbow type
    S: Straight type
    frequency interference
  • Protect aging engines from cutting
  • out in wet conditions
    V: 120º
  • For use with 7mm-diameter plug wires
  • Elbow type
    X: 120º
    T: Special
    Y: 120º Elbow
  • Sold each
  • (long)
    Elbow type
    90º Elbow
    type (short)
    P ART  #
    SUG. RETAIL
    P ART  #
    SUG. RETAIL
    P ART  #
    SUG. RETAIL
    P ART  #
    SUG. RETAIL
    P ART  #
    SUG. RETAIL
    P ART  #
    SUG. RETAIL
    LB05E
    $2.95
    LB05F
    $2.95
    LD05FP
    $2.95
    SD05F
    $3.95
    VB05F
    $3.95
    XD05F
    $3.95
    LB05EP
    2.95
    LB05FP
    2.95
    LZFH
    1.95
    TB05EM
    6.95
    VD05F
    3.95
    YB05F
    3.95
    LB05EZ
    2.95
    LD05F
    2.95
    SB05F
    3.95
    TB05EMA
    5.95
    XB05F
    3.95
    140403
    140403S
    SUPER COIL KITS
    FOR UNIVERSAL APPLICATIONS
  • High-output coils for use in either 2- or 4-cylinder motorcycles
  • Motorcycles with point or electronically triggered ignitions use
  • PART #140403 or #140403S
  • Bikes equipped with capacitive discharge ignition (CDI) use
  • PART #140404 or #140404S
  • ACCEL engineers designed these coils’ special low-resistance
  • primary winding to match the operating characteristics of
    factory and aftermarket CDI systems
  • Maximum performance with fast rise times
  • Extra-heavy-duty 8.8mm silicone wires included
  • Made in the U.S.A.
  • NOTE: Using the wrong coil may damage your motorcycle’s electronic
    2102-0265
    ignition module. To determine your ignition type, complete the following test:
    2102-0266
    1. Determine whether the type of coil you are replacing is a high tower coil. (These coils will NOT replace single tower coils.)
    2. Using a volt meter or 12V test light, hook the positive lead to the positive post and the negative lead to the ground on one of the stock coils.
    3. Turn the ignition on, but DO NOT engage the starter button.
    4. If there are 12V at the coil, the motorcycle has an inductive type ignition. If there is no voltage at the coil, then the motorcycle has a CDI ignition because the
    power goes to the control box first.
    PRIMARY
    SUG.
    PRIMARY
    SUG.
    DESCRIPTION
    P ART  #
    IGNITION TYPE
    RESISTANCE
    RETAIL
    DESCRIPTION
    P ART  #
    IGNITION TYPE
    RESISTANCE
    RETAIL
    4-cyl. model (two-coil kit) 140403
    Inductive discharge 3.0 ohms
    $237.95
    4-cyl. model (two-coil kit) 2102-0266 Inductive discharge 3.0 ohms
    $248.95
    2-cyl. model (one-coil kit) 140403S
    Inductive discharge 3.0 ohms
    131.95
    2-cyl. model (one-coil kit) 2102-0265 Inductive discharge 3.0 ohms
    136.95
    4-cyl. model (two-coil kit) 140404
    CDI
    0.7 ohms
    252.95
    4-cyl. model (two-coil kit) 2102-0268 CDI
    0.7 ohms
    248.95
    2-cyl. model (one-coil kit) 140404S
    CDI
    0.7 ohms
    136.95
    2-cyl. model (one-coil kit) 2102-0267 CDI
    0.7 ohms
    136.95
    UNIVERSAL 8.8MM WIRE SETS
    WITH VARIABLE ANGLE BOOTS
  • High-conductivity, silver-plated copper woven around
  • stainless steel
  • Two 42” wires are included in a 4-cylinder set, one in
  • a 2-cylinder set – each wire can be cut to the desired length
  • Both sets include locking terminals for male coil towers,
  • 170082
    brass distributor terminals and boots for female coil
    towers, butt connectors and shrink tubing for molded coils
    170083
    NOTE: Not for use on 1980 and BMWs.
    FITS MODEL
    P ART  #
    SUG. RETAIL
    FITS MODEL
    P ART  #
    SUG. RETAIL
    4-cylinder
    170082
    $63.69
    2-cylinder
    170083
    $32.43
    DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES.
    SEE PAGE 6 FOR IMPORTANT EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND WARRANTY INFORMATION.
    2018 PARTS UNLIMITED STREET