V-TWIN TOOLS
CRANKCASE
MAIN BEARING
LAP TOOL
  • Performs easy, precise alignment and lapping of right and left
  • crankcase races for oversize bearings
  • Sold individually
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS-196105
    For 84-99 Big Twin (except Twin Cam)
    $809.95
    DS-196212
    CRANK ASSEMBLY
    REMOVING TOOL
    CYLINDER
    TORQUE PLATES
  • Torque plates must be used
  • Made in the U.S.A.
  • when boring or honing late -
    NOTE: On Twin Cam B motor will only remove flywheel from left case.
    model aluminum cylinders
    P ART  #
    DESCRIPTION
    SUG. RETAIL •Simulate running
    DS-196089
    Use on 55-06 Big Twin, except 06 Dyna
    $230.95
    stress conditions
  • Come with instructions
  • Made in the U.S.A.
  • PART #
    DESCRIPTION
    SUG. RETAIL
    CRANKPIN NUT
    3801-0130 For 88”, 96” or 103” 99 - 17 Twin Cam, 3.75” - 3.875”
    $528.95
    CLEARANCE GAUGE
    3801-0129 For 99 - 17 Twin Cam Screamin’ Eagle, 4” - 4.060”
    528.95
    DS-196212 For 66 - 99 Shovelhead/ Evolution cylinders, 3.4375” - 4” bore
    w/ stock bolt pattern
    521.95
    and crankpin nuts when using stroker flywheels
    DS-196213 Adapter bolt kit for 86 - 03 XL, 94 - 03 Buell
    (for use w/ PART #DS-196212)
    40.95
    PART #
    DESCRIPTION
    SUG. RETAIL
    53-0005
    For 58-99 Big Twin motors, except Twin Cam
    $24.95
    TAPPET GUIDE
    PULLER TOOL
  • Used to remove press-fit
  • tappet guides from crankcase
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS-196155
    For 57-85 XL
    $45.95
    3801-0192
    TAPPET GO-NO-GO TOOL
  • If the tip doesn’t fit between the clip and the pushrod seat or if there is
  • For use on most hydraulic tappets, OEM and aftermarket, for Twin Cam
  • or Evo
  • Will not work on Solids, JIMS Hydrosolids or other limited travel tappets
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    Tappet adjustment tool
    $29.95
    3801-0193
    VACUUM LIFTER
    TAPPET PUMP
    “PUMP UP” TOOL
    AND TEST STANDS
  • Bleeds and pumps up hydraulic lifters
  • Allow you to fill hydraulic tappets before
  • Special jar, designed for vacuum, holds up to four
  • assembling valve train
  • Helps diagnose loose or spongy tappets that could eventually lead to
  • Apply the vacuum to fully bleed the lifters and have
  • bleed-down issues or sticky tappets that won’t pump up due to poor
    them ready to install
    hydraulic unit fitment
  • Removes the risk of using the starting system to
  • Made in the U.S.A.
  • pump up the lifters or damage to the valve train at
    PART #
    DESCRIPTION
    SUG. RETAIL
    low rpm if the lifters are not fully bled
    3801-0192
    Tappet pump and test stand for 99-17 Big Twin
    hydraulic tappets
    $281.95
    PART #
    DESCRIPTION
    SUG. RETAIL 3801-0193 1
    Adaptor for 84-99 Evo hydraulic tappets
    69.95
    3801-0292
    For 84-17 Big Twin hydraulic tappet assemblies
    $83.95 1
    Must be used in conjunction with PART #3801-0192.