V-TWIN TOOLS
FLYWHEEL SOCKETS
DS-196104
DS-196111
DS-196110
  • Made of 4130 chromoly steel
  • Available in 1 / 2 ” or 3 / 4 ” drive
  • Machined for 100% nut-to-socket and drive-end contact
  • SPROCKET SHAFT
  • Eliminate nut rounding and risk of injury
  • PROTECTOR CAP
  • Made in the U.S.A.
  • Protects sprocket shaft when using crank
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    assembly removing tool PART #DS-196089 or
    1 / 2 DRIVE
    a press
    DS-196104
    For crankpin nut OEM  #23969-83; L83-99 Big Twin 1 1 / 2
    $79.95
    DS-196111
    For pinion shaft nut OEM  #24016-80; 81-89 Big Twin 1 1 / 4
    79.95
    DESCRIPTION
    SUG. RETAIL
    3 / 4 DRIVE
    DS-198637
    For 55-06 Big Twin
    $46.95
    DS-196110
    For sprocket shaft nut OEM  #24017-80; 72-99 Big Twin 1 5 / 8
    87.95
    MAIN BEARING REMOVER/ INSTALLER
    BEARING AND
  • Removes left and right main bearing without damaging case
  • Provides correct alignment and depth during installation
  • Multi-faceted tool has many uses
  • Made in the U.S.A.
  • Removes flywheel sprocket
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    shaft inner bearing race on 03-07
    3801-0322
    For 17-18 M-Eight
    $190.95
    Twin Cam
  • Can be used to remove Timken ® bearing pinion shaft inner bearing
  • race on 57-07 XL, including all Buells
  • Can also be used to remove press-fit transmission gears and
  • bearings from input and output shafts on all 02-07 V-Rod models
    3801-0099
    3801-0100
    DESCRIPTION
    SUG. RETAIL
    3801-0088
    Bearing and race puller tool
    $322.95
    ENGINE ROTATOR
  • Rotates flywheel/ piston assembly with engine
  • still in frame or on a bench
  • The perfect tool when doing pushrod
  • adjustments, building big-inch engines and
    checking operating clearances
  • Also can be used to keep the flywheel assembly from rotating when
  • torquing the cam drive sprockets retention bolts
    CRANKSHAFT BEARING TOOL
  • Built with a long socket design, making it easier to use without a
  • Used to remove and install the right crankcase
  • 1 / 2 drive extension on your 1 / 2 driver
    bearing in Twin Cam motors
  • Made in the U.S.A.
  • NOTE: Not for use with an air or electric impact wrench; this tool is only
  • Includes instructions
  • guaranteed for use with hand drivers.
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    P ART  #
    DESCRIPTION
    SUG. RETAIL 3801-0099
    For all 07-17 Twin Cam, 06 Dyna Glide
    $117.95
    DS-196194
    For 99-02 Twin Cam A motors
    $189.95 3801-0100
    For 55-06 Big Twin (except 06 Dyna Glide)
    117.95
    3801-0200
    CRANKSHAFT BEARING
    ENDPLAY SETUP TOOL
    RATCHETING CRANKSHAFT WRENCHES
  • For Big Twin engines to set up crankshaft bearing endplay
  • Diameter of the bolt is turned slightly smaller than the actual
  • crankshaft diameter, allowing the inner bearing races to be installed
    and removed without pressing them on or off
  • Chrome-plated with EZ Grip screwdriver-style handle for comfort and
  • Allows much faster changing of shims and faster setup time
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
  • Made in the U.S.A.
  • 3801-0200
    For 55-06 Big Twin (except 06 Dyna); 10-spline
    $55.95 P ART  #
    DESCRIPTION
    SUG. RETAIL
    3801-0207
    For 06 Dyna, 07-17 Twin Cam; 24-spline
    60.95 3801-0196
    For Big Twin engines (except M-Eight)
    $54.95
    COMPENSATOR BOLT TORX ® SOCKET
  • Correct style driver/ socket for the compensating sprocket retaining fastener
  • PART #
    DESCRIPTION
    SUG. RETAIL
  • Made in the U.S.A.
  • 3802-0070
    For 14-18 Big Twin models
    $15.95