V-TWIN TOOLS
CAMSHAFT REMOVAL/ INSTALLATION TOOL
DS-198809
  • Made in the U.S.A.
  • 3801-0068
    SUG.
    P ART  #
    DESCRIPTION
    RETAIL
    DS-196199 For 99-06 Twin Cam (except 06 Dyna)
    for removing/ installing cams and bearings; for 00-06 FXST/FL
    and L00-05 FXD to remove and install cams only
    $193.95
    CAM BEARING INSTALLER
    AND REMOVER TOOL
  • Made from hardened steel
  • Includes removal shaft with installer and hold-down bolts
  • Update kit includes removal shafts required for use on models listed
  • CAMSHAFT
  • Made in the U.S.A.
  • NEEDLE BEARING
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    REMOVER/
    DS-198809
    For 99-06 Twin Cam; repl. OEM  #42325
    $177.95
    3801-0068
    Update kit for 06 Dyna and all 07-17 Twin Cam models
    144.95
    INSTALLER
    the camshaft inner needle bearing in
    M-Eight engines
  • Uses the proven JIMS ® style remover collet and
  • 3801-0061
    fine threaded installation driver
    INNER
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    CAM BEARING
    3801-0316
    For 17-18 M-Eight engines
    $275.95
    REMOVAL TOOL
  • Used to remove inner cam
  • bearing without damaging
    the crankcase
  • Tool is also designed to
  • keep rollers from falling into
    the crankcase
  • Instructions included
  • Made in the U.S.A.
  • CAM BEARING PULLER
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS-196198
    For 00-06 Twin Cam motors (except 06 FXD)
    $176.95
  • Use to remove the cam ball bearings from the
  • 3801-0061
    For 06 Dyna models and all 07-17 Twin Cam
    263.95
    camshafts after they are removed from the
    DS-196156
    For 58-99 Big Twin, except Twin Cam
    185.95
    support plate
    DS-197056
    For 57-90 XL
    184.95
  • Removes bearing straight without binding
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS-196193
    For 99-06 Twin Cam (except 06 Dyna) for
    removal of bearings; for L00-06 FXST/FL and
    L00-05 FXD for removal of front cam bearing
    $239.95
    CAM COVER
    HOLDING TOOL
  • Clamps in vise
  • Holds cam cover flat and helps prevent
  • damage/ scratches when removing and
    installing bushings
  • Made in the U.S.A.
  • CAM COVER PULLER
  • Designed to remove the cam cover
  • P ART  #
    DESCRIPTION
    SUG. RETAIL
  • Made in the U.S.A.
  • DS-196144
    For 70-99 Big Twin (except Twin Cam)
    $101.95
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    For 70-99 74” and 80” Big Twins, and 70-03 XL models
    $16.99
    REAMER TOOL
    FOR CAM PLATE
    RELIEF VALVE BORE
  • Use this reamer to perform a ‘valve job’ on the pressure relief valve
  • seat of any Twin Cam engine cam plate
  • Can be used on OEM or aftermarket cam plates
  • CAM ASSEMBLY TOOL
  • To use, lightly machine the cam plate relief valve seat and re-seat the
  • Holds both cams in an upright position while lowering cam support
  • plunger valve
    plate over both guides and cam journal guides
  • Best used in conjunction with Feuling ® pressure testing tool
  • Made from a non-marring material that will not damage cam surface
  • PART #3801-0071
  • Made in the U.S.A.
  • P ART  #
    DESCRIPTION
    SUG. RETAIL P ART  #
    DESCRIPTION
    SUG. RETAIL
    3801-0066
    For 06 Dyna models and all 07-17 Twin Cam models
    $171.95 3801-0252
    For 99-17 Twin Cam models
    $119.95