V-TWIN TOOLS
CAM OR PINION BUSHING
DS-196099
DS-196101
INSTALLER DRILL JIGS
  • Use to install bushing and drill dowel pin hole to factory specification
    • DS-196313
  • #31 jobber length HSS drill bit included with jigs
  • Made in the U.S.A.
    • DS-196100
    PART #
    DESCRIPTION
    SUG. RETAIL
    PART #
    DESCRIPTION
    SUG. RETAIL
    DS-196100
    For pinion bushing OEM #25582-54/73; 54-92 Big Twin
    $52.95
    (except Twin Cam)
    $52.95
    DS196313
    Staking dowel pins (10-pk.)
    14.95
    motors, 54-18 XL, 91-09 Buell (except 1125R)
    52.95
    CAM/ CRANK
    SPROCKET
    LOCK TOOL
    camshafts and crankshaft
    sprockets when removing,
    replacing and torquing the
    PINION BUSHING PULLER
    DS-196201
  • Use to remove pinion bushing from cam cover
    • sprocket bolts
    in one easy operation
  • Use with cam cover holder PART #DS-196144
  • Made in the U.S.A.
  • Made in the U.S.A.
    • P ART  #
    DESCRIPTION
    SUG. RETAIL P ART  #
    DESCRIPTION
    SUG. RETAIL
    3801-0060
    For 06 Dyna models and all 07-17 Twin Cam models
    $73.95 DS-196157
    For 54-99 Big Twin
    $171.95
    For 99-06 Twin Cam motors (except 06 FXD)
    55.95
    DS-197011
    DS-196044
    DS-196042
    CAM AND PINION
    GEAR GAUGE PINS
  • Use to check pinion gear for pitch diameters
    • INNER CAM BEARING INSTALL TOOL
  • A complete sizing chart is included with the
  • Use to install inner cam bearings
    • .105” gauge pins
  • Check service manual for sizing chart
  • Sold in sets of two
    • P ART  #
    DESCRIPTION
    SUG. RETAIL
  • Made in the U.S.A.
    • DS-196044 Cam bearing tool only for 58-99 Big Twin (except Twin Cam)
    $72.95 P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS-196043 Cam bearing tool only for 57-90 XL, 87-90 Buell
    70.95 DS-197011
    .105” for 54-89 Big Twin
    $30.95
    81.95 DS-197012
    .108” for 90-99 Big Twin Evolution
    30.95
    GAUGE PINS
  • Used to measure the outside diameter of cam drive gears
  • Precision machined from a high-quality steel alloy
  • Available in .105” or .108” dia.
    • DS199105
  • Made in the U.S.A.
    • NOTE: There are two basic differences between 90-99 cam gear sizes and earlier years. The overall range of gear pin measurements (from the largest gears to
    the smallest) was reduced in ‘90 from .006” to .003”. The large gears are the same size for both 84-89 and 90-99 (green and black color codes). Gear size
    measurements (over pins) are listed in the 1990 H-D manual using .108” pins instead of .105” pins (as for earlier years). For the same gear, measurement over
    .108” pins will be approximately .012” larger than for .105” pins. For 92 engines, stock cam gears are interchangeable with earlier versions but gear outer
    diameters have been reduced by .025”.
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS199105
    .105” gauge pins (pr.)
    $19.95
    DS-199106
    .108” gauge pins (pr.)
    $21.95