V-TWIN TOOLS
CAM OR PINION BUSHING
DS-196099
DS-196101
INSTALLER DRILL JIGS
  • Use to install bushing and drill dowel pin hole to factory specification
  • Use staking dowel pin PART #DS-196313
  • #31 jobber length HSS drill bit included with jigs
  • DS-196100
    DS-196313
  • Made in the U.S.A.
  • PART #
    DESCRIPTION
    SUG. RETAIL
    PART #
    DESCRIPTION
    SUG. RETAIL
    DS-196099 For cam bushing OEM #25581-70; 70-99 Big Twin,
    DS-196100 For pinion bushing OEM #25582-54/73; 54-92 Big Twin
    $52.95
    except Twin Cam
    $52.95
    DS-196313 Staking dowel pins (10-pk.)
    14.95 OFFROAD
    DS-196101 For cam bushing OEM #22586-37; 37-48 Big Twin sidevalve
    motors, 54-17 XL, 91-09 Buell (except 1125R)
    52.95
    CAM/ CRANK
    SPROCKET
    LOCK TOOL
  • Designed to lock the
  • camshafts and crankshaft
    sprockets when removing,
    PINION BUSHING PULLER
    replacing and torquing the sprocket bolts
  • Use to remove pinion bushing from cam cover
  • Made of non-marring Delrin ®
  • in one easy operation
  • Comes with instructions
  • Use with cam cover holder PART #DS-196144
  • Made in the U.S.A.
  • DS-196201
  • Made in the U.S.A.
  • PART #
    DESCRIPTION
    SUG. RETAIL P ART  #
    DESCRIPTION
    SUG. RETAIL
    3801-0060
    For 06 Dyna models and all 07-17 Twin Cam models
    $73.95 DS-196157
    For 54-99 Big Twin
    $171.95
    DS-196201
    For 99-06 Twin Cam motors (except 06 FXD)
    55.95
    DS-196043
    DS-196042
    DS-197011
    CAM AND PINION GEAR
    GAUGE PINS
  • Use to check pinion gear for pitch diameters
  • INNER CAM BEARING INSTALL TOOL
  • A complete sizing chart is included with the
  • Use to install inner cam bearings
  • .105” gauge pins
  • For use with handle PART #DS-196042
  • Check service manual for sizing chart
  • Made in the U.S.A.
  • Sold in sets of two
  • PART #
    DESCRIPTION
    SUG. RETAIL
  • Made in the U.S.A.
  • DS-196044 Cam bearing tool only for 58-99 Big Twin, except Twin Cam
    $72.95 P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS-196043 Cam bearing tool only for 57-90 XL, 87-90 Buell
    70.95 DS-197011
    .105” for 54-89 Big Twin
    $30.95
    DS-196042 Handle/ driver only
    81.95 DS-197012
    .108” for 90-99 Big Twin Evolution
    30.95
    GAUGE PINS
  • Used to measure the outside diameter of cam drive gears
  • Precision machined from a high-quality steel alloy
  • Available in .105” or .108”  dia.
  • Sold in pairs
  • Made in the U.S.A.
  • NOTE: There are two basic differences between 90-99 cam gear sizes and earlier
    DS199105
    years. The overall range of gear pin measurements (from the largest gears to
    the smallest) was reduced in ‘90 from .006” to .003”. The large gears are the
    same size for both 84-89 and 90-99 (green and black color codes). Gear size measurements (over pins) are listed in the 1990  H-D manual using .108” pins instead
    of .105” pins (as for earlier years). For the same gear, measurement over .108” pins will be approximately .012” larger than for .105” pins. For 92 engines, stock
    cam gears are interchangeable with earlier versions but gear outer diameters have been reduced by .025”.
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    P ART  #
    DESCRIPTION
    SUG. RETAIL
    DS199105
    .105” gauge pins (pr.)
    $19.95
    DS-199106
    .108” gauge pins (pr.)
    $21.95